

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 25+: 60 results shown for flywheel.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- '66 progress, On the Road a-gin...Historical mailing listMon, 10 Jun 1996 10:21:48 -0700...bottom of the bell-housing without interfereing with the flywheel, but with a 12V flywheel in a 6V bell-housing, the clearance is very...
- Re: 85 GL Engine ExchangeHistorical mailing list - Joseph FortinoFri, 8 Feb 2002 14:52:09 -0800...Replace the clutch and check the flywheel while it's > out. > Special tools? Hammer type impact driver, torque wrench, some method > for > locking the...
- Re: FS: VR6 engine w/o ECU & harness for conversion. Also safari
roof rack & 16" Ronal R9 copiesHistorical mailing list - Sudhir DesaiFri, 20 Jan 2006 10:05:16 -0500...Came from a > Passat with auto trans so no flywheel if you are converting a manual car or > van. Donor had 92,000 miles...
- Re: Pilot BearingHistorical mailing list - Mark DearingWed, 8 May 2013 11:29:18 -0400...The roller bearings had fallen out of mine and were wedging between the flywheel and the rear main seal causing a big oil leak.
- 2.1 for saleHistorical mailing list - Bill MSat, 4 Sep 2010 21:04:27 -0400...Still has flywheel and clutch on it. The only catch is it must be picked up in mystic,ct. Price 150.00. Bill P...
- weights of enginesHistorical mailing list - William R. Kennedy, NJIT CIAT, 201-596-5648Fri, 10 Feb 95 09:32:22 EST...Engine weights, less flywheel, clutch, and "options": 1600cc VW 215 Porsche 914 265 VW Type 4 311 Porsche 911 280 Mazda rotary 260 Ford...
- Re: Yow! - loose '73 engine mountingHistorical mailing listTue, 09 Jul 1996 15:19:07 -0400...Often times folks buy a > long block, stick on their flywheel and go. Massive imbalance. This brings a question to mind. Since my recent...
- '79 2.0 liter engine & tranny for saleHistorical mailing list - R.D. RobertsonWed, 30 Oct 1996 00:39:13 -0600...bus are for sale, along with a good pressure plate and flywheel. Both engine & tranny worked fine when I replaced them, I just wanted...
- Re: Vanagon cylinder orderHistorical mailing list - Marshall RuskinFri, 26 May 2000 12:46:29 -0500...Maybe that's why I can't get my timing ever set right? ;>) Marshall >Uh...Marshall? Try again... > > > Flywheel >3 1 >4 2 > Pulleys...
- Re: Rear? You mean FRONTHistorical mailing list - Andrew GrebneffTue, 24 Jul 2001 21:39:41 +1200...Front end of engine is that closest to headlights, no matter whether it has a pulley or flywheel attached. Such usage is NOT defined...
- Re: pilot bearing/clutch problemsHistorical mailing listTue, 29 Nov 94 12:40:20 AST...Note the position of the plate relative to the flywheel, mark it somehow! Once you get the plate off, the disc should be disgarded...
- Re: Crank Scoring / Flywheel sealHistorical mailing list - Jim FelderFri, 10 May 2013 07:37:29 -0500...my next question - I've heard the warnings when removing the > flywheel seal (rear main seal) that you want to be sure not to...
- Re: Cracked Syncro Clutch HousingHistorical mailing list - W.R. TransueMon, 12 Aug 96 16:27:54 -0500...Cracked Syncro Clutch Housing > > Bill, first the oil leak is probably coming from your front(rear main) flywheel > oil seal.There is no oil...
- Re: 5 cyl. Audi, sender on flywheel doesn�t matterHistorical mailing list - John ReynoldsTue, 15 Aug 2000 19:01:50 -0400MArk, I believe that our octane is actually has more "Umph". I believe that the average method lessens the rating. Anyone out there who...
- Re: 5 Cylinder conversionHistorical mailing list - Ben TTue, 15 Jul 2003 05:13:34 EDT...their > Transporter? if so how did you sort out bellhousing and flywheels? Winkler was selling kits for these at one time. Last I heard...
- Re: Front and rear seal replacementHistorical mailing list - Jack R.Sat, 19 Jan 2008 06:44:30 -0500...Also, the time to take to clutch, flywheel and pressure plate to a local clutch resurface place. One other note: the throw out bearing...
- Engine Oil Seal (and similar) vs Axle Bearing Grease Seal, InstallHistorical mailing list - Neil NTue, 10 May 2016 15:55:08 -0700...from flywheel hub, wheel hub. Why I think this is true. Again, please correct me if I'm wrong! - if a seal is more...
- Re: 84' Vanagon starter falling apartHistorical mailing list - Scott Daniel - TurbovansTue, 25 Jan 2011 13:52:29 -0800...if the gear ratio starter to flywheel was not 30 to one or whatever it is, you'd need one huge starter to spin...
- Re: removing wrist pin on #1 & 3Historical mailing list - Kenneth WilfordWed, 23 Aug 2006 08:37:48 -0400...Sneak the nut in place at the end of the wrist pin (toward flywheel) and turn the threaded stock until the nut is firmly...
- Re: Soo- Oil Pan crackedHistorical mailing list - Greg PottsMon, 5 Nov 2012 22:35:23 -0500...ell.... > there can be a gotcha. > check this part first thing ..by the flywheel ... > if it has stock 5mm allen screw pan screws ... > you...
- Re: Forwarded: Suspicious Syncro Shifting SymptomsHistorical mailing listWed, 7 Feb 1996 11:24:26 -0500...replace the input seal, I noticed the pilot bearing in the >flywheel/crankshaft was non-existant. With the bearing gone the input shaft >wobbled...
- Re: optical distributorHistorical mailing list - Robert LilleyFri, 21 Jan 2000 09:02:29 EST...I have been thinking about a system for my 73 Bus T4 engine to come off the TDC dowel pins in the flywheel. I...
- Re: Diesel: Temp gauge gone crazyHistorical mailing list - David BeierlSat, 26 Jan 2002 21:25:01 -0500...I understand. >There appears to be two sensors, one at the flywheel end of the head and >another in the outlet where the thermostat...
- Vanagon starter final drive issues?Historical mailing list - DennisMon, 6 Dec 2004 22:37:16 -0500...Increasingly, (about 50% of the time) the starter spins up, but does not engage the flywheel. Naturally it never did this before the rebuild...
- Re: Engine balancingHistorical mailing list - Robert LilleyThu, 2 Dec 1999 00:16:09 EST...Then the flywheel is attached and it is spun again and balanced. Then the hub is attached and the process is done again, then...
- Re: visit to GEXHistorical mailing list - Dave KautzTue, 7 Nov 95 11:41:27 PST...Good used type I cases and 215 mm flywheels for 74-75 buses are the scarce items. Leonard was more interested in the flywheel...
- Re: Longer Lasting Clutch?Historical mailing list - Max WellhouseSat, 23 Apr 2011 01:09:43 -0500...running a Kennedy "WBX" >>flywheel) >> >>Any users running a more robust non stock clutch on stock clutch >>housing/flywheel? Has it lasted longer under...
- Re: Clutch problemsHistorical mailing list - Herr Wibo FichtenSun, 18 Jan 2004 20:40:54 -0400...the clutch was burned and > worn, and the flywheel was uneven. > > So a changeover, skimmed flywheel was installed, with a new Sachs(?) clutch > plate...
- Re: Timing Notch? on 2.1 DigifantHistorical mailing list - kenneth d lewisMon, 15 Sep 1997 18:49:57 EDT...writes: >I have some confusion regarding the timing notches on the flywheel: >-------------^---------F >-----u-----------------R >When setting the timing (Temp Sender II disconnected, revs...
- Re: synthetic oil (switching teams)Historical mailing list - Kenneth D LewisSun, 7 Feb 1999 13:29:56 -0500Jon; FWIW:I put it in a freshly rebuilt 1.9L engine and developed a leak around the flywheel/crankshaft seal. Switching to Castrol...
- Re: Cylinder identificationHistorical mailing list - Jonathan FarrugiaMon, 2 Jan 2006 18:57:46 -0500...there is the ascii picture which is only worth 500 words :). Flywheel End (towards passenger compartment) --------- 3----| |----1 4----| |----2 The Volkswagen Bentley Manual...
- Re: Hello again, Brakes, No-Start, Coolant bleeder, 1985 GLHistorical mailing list - Lawrence JohnsonWed, 08 Jan 1997 20:03:34 -0800...but the binhex doesn't pull out to engage with the flywheel to turn the > > engine over. One way to get the Vanagon going...
- Re: "Wish in one hand, _____ in the other..." Clutch ?Historical mailing list - Raymond PaquetteThu, 23 Sep 2010 06:53:34 -0400...I > re-used the clutch and flywheel from my 1.8liter block, un-touched, on the > "new" 2.0liter block. I did not replace...
- Re: 86 Vanagon - New Owner - A few Questions.Historical mailing list - John RodgersMon, 21 Aug 2006 21:31:00 -0500...Be sure the flywheel face is machined true before re-installation, and have a new flywheel seal installed. (main seal). Any time I have...
- Re: "Wish in one hand, _____ in the other..." Clutch ?Historical mailing list - Scott Daniel - TurbovansWed, 22 Sep 2010 11:10:01 -0700...That's so appreciated ! same flywheel and pressure plate and disc as before ? the precise same ones just bolted to the new 2.0...
- head scratchin fun with the 2.3Historical mailing list - Patrick DooleyWed, 8 Apr 1998 15:43:41 -0400...The flywheel they sent was 200mm. 28mm smaller than 091 flywheel and may not work at all. I.E., don't pull your credit...
- Re: Shuddering clutch engagementHistorical mailing list - Michael S. NicholsSun, 16 Apr 2000 23:11:45 -0400...The flywheel is a bit >discolored toward the center area where the clutch contacts it but looks OK >on the outer area. The inner...
- Re: [Syncro] FREE syncro waterboxer core engine. NYHistorical mailing list - Dylan FriedmanSun, 15 Aug 2010 20:45:08 +0000...Recently pulled from running van. Bottomend is good. one head good. Flywheel and clutch still attached intake usable syncro headers rockers lifters......FREE. > pmail...
- Re: Starter click, no crankingHistorical mailing listSat, 31 Oct 1998 08:30:19 EST...This may unjam your starter gear (if that has somehow become stuck against the flywheel). If the motor will turn freely then check your...
- Re: DIESEL CONVERSION PARTSD WANTEDHistorical mailing list - PuzerewskiTue, 13 Jun 2000 04:16:06 -0400...BUT ALL THE OTHER STUFF-OIL PAN, ENGINE CARRIERS, OIL PUMP, FLYWHEEL, TRANS BELL HOUSING, ETC. USED PARTS ONLY (NOT LOOKING TO PAY TOO...
- Re: Swapping '86 front end onto '82Historical mailing list - Roger SislerThu, 10 Feb 2005 16:39:59 -0500...only way to go(expensive hindsite) .That arm acts like a flywheel and absobls road shock instead of transmitting it to you.To do...
- Re: Pilot bearing failureHistorical mailing list - Dennis HaynesSat, 15 Aug 2015 00:10:20 -0400...When the flywheel goes on it will collapse the outer shell and the input shaft will not be able to spin free or it...
- Re: Possible to swap Auto to Manual?Historical mailing list - Stan WilderWed, 28 Aug 2002 18:57:46 -0500...You need > the tranny, flywheel, clutch, starter,the complete shifter and > linkage, both MT halfshafts, the pedal assembly, master and slave > clutch cylinders and...
- Re: Shifting Shudder Part IIHistorical mailing list - Al and Sue BraseFri, 17 Sep 2004 02:16:52 -0500...engine mounts, transmission >mounts, TO bearings, clutch slave cylinders, friction plates and have >had flywheels resurfaced, all at the advice of supposedly helpful >list...
- Re: More Clutch - Pilot Bearing NightmareHistorical mailing list - Scott Daniel - TurbovansTue, 8 Jun 2010 21:11:40 -0700...I cannot see any different bearing for the job on the Depot site. > Are there different flywheels and bearings on an 86? Am I...
- <no subject>Historical mailing list - Nathaniel PooleTue, 17 Oct 2006 17:55:18 -0700...and the typical leaks are there-pushrod seals, rocker cover and flywheel. What I didn't expect to find was apparent oil seepage from...
- Re: New engine won't turn - 2.1 WBXHistorical mailing list - Dennis HaynesThu, 31 Dec 2015 22:43:32 -0500...There is the >>> thrust washer that can easily drop out of place when you install the >>> flywheel. Or you miscalculated the thickness of the...
- Re: Timing Notch? on 2.1 DigifantHistorical mailing list - Tom BrunsonMon, 15 Sep 1997 23:42:59 UT...I suspect the flywheel TDC sensor used by VW is more accurate than the pulley notch. Since VW uses the sensor they may not...
- Re: Roadhaus - 2.2L Engine Install , Prelimanary ReportHistorical mailing list - Kim BrennanWed, 16 Oct 2002 12:49:10 -0400...There is always some loss of HP in the translation from the flywheel down to the wheels. So if someone else reported HP for...
- Clutch experts...a couple of questions...ASAPHistorical mailing list - AaronWed, 15 Jun 2005 11:09:35 -0700...I just replaced my clutch (first time) and had my flywheel resurfaced. I have a subaru vanagon and the old clutch had developed some...
- specs for the 3 roll pins and six bolts for the clutchHistorical mailing list - nirav patelThu, 31 May 2012 16:38:54 -0500...the following? � 3 roll pins that align the clutch to the flywheel � 6 bolts for the clutch I called my local VW pick-n...
- Re: Separating the Engine Case. Any tips?Historical mailing list - Chris S.Wed, 11 Jan 2012 18:36:57 -0500...The case is shot. > I'm ready to go in through the side..... : ) > > I still have the flywheel and rear pulley on. Is that...
- Clutch removal - Oil sealHistorical mailing list - Kurt GrotzSat, 8 May 2010 11:40:03 -0400...Found some great step by steps on line and have everything I need (almost) Question is.....if the flywheel looks ok, do I need...
- Re: Front Oil Seal vs Flywheel Seal vs Bob Donalds Installation VideoHistorical mailing list - RolandThu, 19 Mar 2009 07:27:00 -0700Hi Mike, about "...the same part number is used for both a 10mm and a 12mm seal. " Yikes, I am not doing this project...
- Re: Top Dead Center sensorHistorical mailing list - Aristotle SaganWed, 14 Nov 2001 13:00:21 -0800Someone correct meeze if I am wrong, but the Air Cooled TDC sensor mounted in the engine flange behind the flywheel is for diagnostic...
- Inline conversion parts-four and five-cylinderHistorical mailing list - WestymanMon, 30 Aug 2004 15:01:12 -0700...Includes both support bars, mounts and aluminum castings, bell housing and dust shield, starter, oil pan, oil pick up, flywheel, and many of the...
- Re: Q: Porsche 914 engine compatibility with VanagonHistorical mailing list - ROBERT DONALDSThu, 23 Sep 2004 08:16:53 -0400...the flywheel is differant and the needle bearing at the end of the crank that supports the inputshaft might not be able to go...
- Re: Slipping clutch, rookie ownerHistorical mailing listTue, 18 Jul 1995 19:34:00 -0800 (PST)...the clutch is attached to the flywheel. if you do it, replace the whole thing: clutch disc, pressure plate, flywheel oil seal, throwout bearing...
- Re: Vanagon/Subaru conversionHistorical mailing list - Neil NWed, 3 Jan 2018 09:08:12 -0800...linkage + custom linkage parts, Small Car clutch housing, and probably their flywheel and clutch. https://tinyurl.com/y7q8ef5s I think this subarugears link should...
- Re: Pilot bearing failureHistorical mailing list - vw_van_fan_MarkThu, 13 Aug 2015 13:14:05 -0700...Many of them were on the flywheel. What I am worried > about is the ones that potentially went into the motor. Is that possible...