

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 24+: 60 results shown for Ignition wires.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Re: OXS LEDHistorical mailing list - Dan BeattyTue, 14 Nov 1995 21:43:54 -0600 (CST)...Anyone know where it >is? I'm also starting to get the ignition cut-out that was briefly discussed >a short while back, possible...
- Re: OXS lightHistorical mailing list - Dennis HaynesWed, 20 Jun 2007 09:19:35 -0400...When the ignition is turned on, before the engine is started, the alternator light and O2 light should light solid and the oil pressure...
- Re: '86 Westy cranking troubleHistorical mailing list - neil NSun, 20 Apr 2008 09:51:52 -0700...Also, realize that the green wires to/from the coil are for > ignition pulses not power. > > Your use of a jumper wire to test...
- diagnostic help? running rich(?)...Historical mailing list - Don HansonWed, 23 Jul 2014 15:39:06 -0700...It began running very rough, but running smooth again for a few seconds after turning off the ignition and back on...So I 'nursed...
- Re: 1985 Vanagon GLHistorical mailing list - Rod SmithSat, 19 Aug 2006 19:33:32 -0400...They could not fix it, as it shows evidence of new > plugs, > wires and other parts, jumper wires in the front driver floor...! It...
- Re: Throttle Switch and Failure to Start.Historical mailing list - Dennis HaynesSun, 19 Apr 2015 22:14:16 -0400...not starting look for moisture under the distributor cap or bad ignition wires. Dennis -----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon...
- Re: Power Window Failure DiagnosisHistorical mailing list - developtrustSun, 18 May 2003 10:44:54 -0700...I sliced it open with a razor to access the wires and found the broken one. Fortunately for me the broken wire was right...
- Re: Last word on tach going to zero?Historical mailing list - DennisThu, 3 May 2007 11:54:40 -0400...The power for the ignition goes from the switch, into the fuse box, and back out. The connections on the plugs are known to...
- Re: Compu fire QuestionHistorical mailing list - Stan WilderMon, 1 Oct 2001 08:13:19 -0500...The wires to the pickup unit are so fragile that they move up into the rotor travel unless you have the nylon separator disk...
- Re: Anyone have this tech text?Historical mailing list - Blake HeinleinTue, 31 Jul 2001 16:37:15 -0400...If you're not sure which of the wires to the solenoid is the one from the ignition switch, put a volt meter in...
- Re: delayed startHistorical mailing list - TJ HanninkThu, 7 Feb 2002 21:22:09 +0800I have the same problem with my van and just figured out that mine would eventually turn over after I held the ignition key...
- Vanagon GL 90 2.1L engine unexpectedly stalls while drivingHistorical mailing list - TinkerManWed, 19 May 2004 15:25:15 -0700...I switch the ignition, as it should. I usually play with the AFM connector, remove and replace the HT wires from the distributor, etc...
- Re: Bummer, man--Gross PolluterHistorical mailing list - Old Volks HomeWed, 23 May 2007 15:33:26 -0700...http://www.oldvolkshome.com/ignition.htm#V8384 -- Jim Thompson 84 GL 1.9 "Gloria" 84 Westfalia 2.1 "Ole Putt" 73 K Ghia Coupe...
- Re: YAHOOOO (well, almost)Historical mailing list - Doktor TimSun, 3 Nov 2002 12:57:23 -0800...The opening paragraphs of the FI section in Bentley clearly states verifying no vacuum leaks, no ignition problems, then verify grounds and terminals BEFORE...
- Re: Maybe some VCHistorical mailing list - pdooleySat, 26 Dec 2009 17:54:39 -0500...Probably unrelated to you're problem, the ignition switch can act up too. My friend's 92 GTI, same management as your car, wouldn...
- Re: Vanagon DirvabilityHistorical mailing list - bob tickleMon, 14 Oct 1996 20:23:46 -0400...Check the resistance of all wires. Coil wire value is 2000 Ohms resistance and plug wire value is 6500 Ohms resistance. Ignition System Check...
- F.S. 87 Westy in UTAHHistorical mailing list - Damian ShawMon, 31 Jul 2000 11:55:35 -0600...Very new tires, very new brakes, new rear shocks, new ignition stuff (cap, rotor, wires). Synthetic oil since I've owned it - including in...
- 1983 Water cooled running rough?Historical mailing list - wayne withersMon, 9 Apr 2007 21:00:18 -0700...I must also admit that I have not tested the ignition timing yet. It will randomly run well. The problem is most prominent at...
- Re: [vanagon] lister needs help on the road - headlight gremlin in 86 westyHistorical mailing list - Don in North CarolinaTue, 19 Jul 2005 14:08:28 -0400...When I got to my destination the > switch was melted in the ON position, and I was forced to unplug the wires to > the...
- Re: 87 2.1 loss powerHistorical mailing list - Amy MinerWed, 17 Jun 2009 18:20:14 -0400...I guess I could pull wires and see if I get any big change in running. --- On Mon, Jun 15, 2009 at 11:35...
- Re: 1.9 Running issues when wet outHistorical mailing list - Larry AlofsSun, 23 Jan 2011 07:59:38 -0500When it's running OK take a spray bottle and mist the ignition wires, distributor cap, and coil, etc. with water. If you do...
- Re: Loss of power - super hot mufflerHistorical mailing list - Alfred BagdanSun, 8 Dec 2002 19:59:54 -0700...it might be time to swap in a > new set of ignition wires. On the way home from the airport the power > loss worsened...
- Re: Electrical Gurus help needed 88 van.kinda longHistorical mailing list - mark drillockSat, 27 Jul 2002 15:33:42 -0700...switching itself off after the starter engages. > > Then I Chase wires from the ignition switch to the fuse box, Spray DeOxit on them, and...
- V6anagon Chronicles /LHistorical mailing list - Maher, Steve (SD-MS)Mon, 18 Dec 1995 12:59:00 -0800 (PST)...Cap, rotor, plugs, wires. '80 GM distributor has electronic ignition, with vacuum and centrifugal advance, and has the coil built into the cap (?). Not...
- Re: firing on 3 cylinders.Historical mailing list - John RodgersMon, 20 Nov 2006 08:50:37 -0600...It is eithro or - ignition or fuel. Good luck. Regards, John Rodgers 88 GL Driver craig cowan wrote: > Hello again. I had my engine...
- Re: Vanagon engine fire or mishap in Roanoke, VaHistorical mailing list - Don HansonMon, 6 Dec 2010 17:21:49 -0800It's pretty easy to see shorting plug wires in dark. It doesn't have to be totally inky black darkness, either. Inside a...
- Re: '86 Vanagon Starts, Dies....Revisited (Help!)Historical mailing list - David DustanSun, 16 Jan 2000 11:35:38 -0800...replacing the ignition switch. >> >>Since I last wrote a note the following has been replaced: >> >>Ignition Switch >>Plugs >>Cap >>Rotor >>Wires >>Coil >>Fuel Pump...
- Re: Re-introduction & Dash Removal QuestionHistorical mailing list - Neil NSun, 23 Feb 2014 16:10:34 -0800...If you see evidence of rodent ingress, check the wires for any rodent damage. I doubt it will show wear, but check for excessive...
- Re: Bad ground. WAS; Hmm. Headlights don't ...Historical mailing list - mark drillockMon, 15 Nov 2010 05:42:25 -0800...The relay kits are a great idea to reduce the load on the ignition switch and headlight switch. Making the front grounds independent and...
- Tach Install Complete on 84 WestyHistorical mailing list - Garrick ChangThu, 30 Apr 1998 11:43:41 -0800...First is that there are 2 brown wires on my van but only one coming out of the donor vehicle(84 Wolfsburg). I got...
- 87 GL: One Problem Solved - and a New OneHistorical mailing list - LarryWed, 3 Jan 2001 20:53:50 -0500...No identifiable set of circumstances, but always cured immediately by the Microsoft solution - switching the ignition off and restarting. The loss of power condition...
- Re: Vanagon.com siteHistorical mailing list - Peter CassidyWed, 13 Dec 2000 02:03:54 +0000...breaks into my Vanagon, breaks the steering lock, hot wires >it (or picks the ignition lock) and drives it even a foot, they have...
- Re: start - won't sart - solutionHistorical mailing list - Mike PedersenFri, 22 Aug 2003 17:52:17 -0700...First which temp sensor > did you replace? So far I have eliminated the plugs, wires, > distributer, and coil in the ignition system as possible...
- Wet weather power lossHistorical mailing list - Helen FahyFri, 6 Apr 2001 18:32:50 -0400...I am trying to understand the relationship between the tachometer display and the loss of power and the physical devices in the ignition system...
- Rebuild cost - the grand total!Historical mailing list - Dave KautzThu, 13 Jul 95 15:57:52 PDT...fuel pump, rebuilt the carbs, cap, rotor, spark plug wires, changed to transistorized ignition, put in a new engine compartment seal and replaced EVERY...
- Re: Super high HC on smog test - helpHistorical mailing list - Dennis HaynesThu, 28 Jun 2007 23:41:57 -0400...Is it this bad only at idle? Over advanced ignition timing can cause a high idle with insufficient air flow which will effect HC...
- Re: Key in power - no start situationHistorical mailing list - Richard KoernerFri, 5 Nov 2021 00:32:57 +0000...the ignition switch, safety switch at the transmission (it’s an automatic), the starter itself, along with various ground straps and power wires, the...
- Re: no cold start/hard start relay kitHistorical mailing list - Stan WilderSun, 20 Jan 2002 18:15:13 -0600...The problem probably comes from the > ignition > > > switch or the wires. I've heard about hard start relay bosch > kit. I'm > > > wondering if...
- Re: Sluggish starter fixHistorical mailing list - Scott Daniel - TurbovansWed, 29 Feb 2012 18:06:38 -0800...as in old tired wires .. as in weak igntion switch. when you wire a relay in like this .. rather than having to fire the...
- Re: Starter Power QuestionHistorical mailing list - mark drillockMon, 9 Jun 2014 11:14:47 -0700...Once the engine is running the power flows back the other way over the same wires. Alternator to starter to battery. There is another...
- Re: coolant sensor and startingHistorical mailing list - David BeierlThu, 22 Jul 2010 12:56:29 -0400...If you're talking about the Temp-II sender in the thermostat housing, get it into the no-start condition, then with ignition on...
- Vanagon no start problemHistorical mailing listThu, 11 Apr 1996 23:29:45 +0000 (MULTINET_TIMEZONE)...I think that it must be that the wires going to the ignition switch and back are just be too long and they drop...
- Re: Looking for spark plug wire recommendationsHistorical mailing list - Hector ZapataThu, 1 Nov 2012 19:42:19 -0400Many OEM ignition parts were made by Beru, not Bosch, and I believe those are still German made. On Thu, Nov 1, 2012 at...
- Re: Headlight Upgrade EilemmaHistorical mailing list - John RodgersThu, 8 Sep 2011 19:04:23 -0500...Part of this requires cutting some > wires and these wires are clearly identified in the instructions. When I > went to do this, and removed...
- Re: no fuse for fuel pump? Adding fuses.Historical mailing list - John RodgersSun, 12 Mar 2023 13:26:36 -0500...For > most VWs not having the ignition and fuel systems fused is normal, going > Back to even the very first Beetles. Likely the plan...
- Re: Fixed: Won't Start in St. Helena, Napa CountyHistorical mailing list - Dennis HaynesTue, 2 Dec 2014 23:36:27 -0500...And Now I have a new coil, ignition wires, distributor cap and rotor, too. The fellow at the shop felt the plugs were quite...
- Re: Engine Shudders -2.1L WBX.Historical mailing list - Stuart MacMillanWed, 24 Sep 2014 19:23:09 -0700...I checked with an induction timing light the firing of each ignition wire up 2500 rpm. Each was good. Yet it still shudders on...
- Re: Rainy Day Blues, HELP!Historical mailing list - ERIC ZENOThu, 1 Aug 1996 23:16:45 -0400 (EDT)Try this...as your driving and it's running bad, turn off the ignition switch for 1 second. If it runs good for the...
- Installed new clutch, "used-in-good-condition, recently-rebuilt transmission, and, now, "no start."Historical mailing list - Thomas D. HanlonTue, 4 Jun 2002 18:52:05 -0700...Before dismantling any components, I tagged all the wires and connections. The battery is charged. to capacity. The ignition switch is operating as it...
- Re: Bucking questionsHistorical mailing list - R BlakeMon, 3 Jun 2002 21:39:11 -0700...you mention cold and wet, is ignition stuff like dizzy cap cracks (lets in moisture). Spark plug wires burnt or dying can cause the...
- Re: Bad ground. WAS; Hmm. Headlights don't ...Historical mailing list - RobSun, 14 Nov 2010 21:17:01 -0800...Headlights don't ... >>> >>>Probably the ignition switch. >>> >>>If I remember correctly, power for that circuit >>>comes from the ignition switch. >>> >>>JB >>> >>> >>>On 11/14...
- Re: Flashing Coolant Light Sensor TestHistorical mailing list - Mike CollumMon, 19 Jun 2006 13:08:03 -0400...Try turning on the ignition and waiting for 5 or 10 seconds before starting the engine and see if there is a difference. Mike...
- Re: Is my Aux Battery Charging - NOTHistorical mailing list - mark drillockFri, 15 Jul 2011 11:06:50 -0700...Unplug the wires and measure the voltage on all of the wires with the engine off and then again with the engine running and...
- Re: My fool injectionHistorical mailing list - Dave KautzFri, 3 Feb 95 9:33:24 PST...Well now that the > list has grown mabey someone with the fix has arrived. > > The probelm is that when the ignition is on the...
- All you want toknow about Auto electrical, was: tracing electrical problemHistorical mailing list - Bulley-Hewlett & AssociatesTue, 6 Oct 1998 17:47:02 -0400...In a simplified view of your car(forget about the ignition system, and charging the battery), if you started the car, and the alternator...
- Re: fuel pump?Historical mailing list - Tony MysykThu, 28 Aug 1997 00:38:01 -0600...It was relayed to me that if any ignition wires were bad then they would short to ground when wet, no luck on the...
- Re: GOWESTY AFM no start problemHistorical mailing list - Scott - IMAPSun, 3 Jul 2016 13:27:09 -0700...the ECU just reads change in resistance of almost invisible tiny wires in the air flow inside the Mass Air Flow Sensor. here is...
- Starter relay bypass repostHistorical mailing listTue, 12 Dec 1995 09:25:03 -0500...you're not sure which of the wires to the solenoid is the one from the >ignition switch, put a volt meter in line...
- Re: [Re: Engine Computer Software Glitch???]Historical mailing list - Fred S.Mon, 28 May 2001 23:26:11 MDT...I've replaced the following (in part thanks to suggestions from the list): - O2 sensor - Air flowmeter (with a re-built) - Ignition wires, rotor...
- Re: StereoHistorical mailing list - Jim ArnottTue, 9 Sep 2008 08:46:37 -0700...Most wires on the backside are red. Always 'hot') the 12v power goes to the rear slot of where the key buzzer used to...